How To Install An RV Backup Camera

If your RV did not come with a rear view camera, don’t despair! This article will help you choose the perfect back up camera and tell you how to install it.

First off, be warned that there are a lot of inferior, poor quality backup cameras available on the market today. These cheap units are often poorly rated and a waste of money. For expert advice on this subject, we turn to long time RVers, Jerry & Cynthia of RV Roadtrip.

81NhpWPY3xL._SL1500_

FREE Subscription
RV Magazine

GET IT NOW No Credit Card Required

amazon.com

As seen on CNN, New York Times, and CNBC: Find out how much money you can make renting your RV Click Here

They recommend avoiding  brands such as Pyle, XO, Hootoo, Peak and Boyo. They found that these units performed very poorly and caused far more frustration than they were worth.

Jerry & Cynthia’s pick for the best RV backup camera is the Rear View Safety RVS-7770613 which can be purchased through from the Rear View website, or Amazon.com.

RVING TO ALASKA Download

Tell us where we can send you the guide

RV LIVING A STEP-BY-STEP GUIDE Download

Tell us where we can send you the guide

GUIDE TO RV BOONDOCKING Download

Tell us where we can send you the guide

See More Free Guides

This 7″ LCD color rear view backup camera offers both audio and video, and is the leading manufacturer of backup cameras in the U.S. The folks over at RV Road Trip loved their solid reputation and the quality product that they provide.

When you receive your camera and open the box you will find the following items:

  • A 130 degree wide angle color backup camera. This camera is waterproof and infa-red.
  • A LCD 7 ” rear view color monitor along with a mount, a stand, and the wire.
  • A 3 channel controller along with a wireless remote.
  • A 66 foot extension cable, a power wire, and a double RCA cord to connect your audio, video and power.

Before you start, be sure to make sure EVERYTHING you need is in the box. You don’t want to discover during the install that something it missing. Also test it all to make sure it is working prior to your installation. If you check it before you mount it you will know if you need to fix something other than a faulty unit.

Installation:

Here are the tools you will need for installation of the RV backup camera:

  • A drill with a 3/4 bit
  • A screwdriver set
  • Some RV sealant such as ProFlex

You will also need to be in a calm, patient mood because anything you do with an RV takes time. Be sure to have some wire ties handy as they can help secure things underneath your rig. If all goes well you will need about 2 hours for this install — remember, every RV is different.

In most cases the rear view camera on an RV is mounted just below the clearance lights. Check online for examples before you start. If your clearance lights are low it shouldn’t be a problem, but again this will vary from rig to rig.

  1.  Grab a pencil and mark where you plan to drill the 3/4-inch hole for your wire. Make SURE there aren’t any other wires in the way. You do not want to cut through anything and cause problems. Check for wall studs that might be in the way. Once you know everything is clear you can drill the hole.
  2. Choose how to route your wires. You can use the ceiling rafters or travel underneath the rig. It really depends on your RV. You can also drill through your kitchen cabinets and go through the floor if needed. Spend time accessing the best route PRIOR to drilling your holes.
  3. Drill holes as necessary and route the wire from the inside to the outside. Be sure to fill the holes up with the ProFlex sealant. You do not want bugs or cold air coming in.
  4. Align the camera, connect the wire and test the angle of the view.  Make sure to adjust it several times to check your options. Once you have chosen the specific spot for the camera screw it into place. You will need to use sealant all around to avoid moisture build up.
  5. Plan your wire route for under the RV. Be sure to avoid areas of heat or pinch points. You also want to find a route that allows you to mount the wire with zip ties.
  6.  If you have extra cord you will need to wind it and store it somewhere near the dash. Some people tuck it in or under the dash.
  7. Now you need to mount the monitor in a place you can easily see when driving. Be sure you have a cigarette lighter plug close by as this will be your power source. You can also choose to only use your rear view camera when you are in reverse. If you choose this option you will need to connect your backup light with the blue wire offered in your kit. If you want it on all the time you will need to twist the red and blue wires together so it will be on anytime you have the monitor plugged into the lighter outlet.
  8.  Test the unit. What do you see? Is the angle of the camera correct? Is the monitor in a comfortable position? Check the wires again to make sure they are all properly connected and secured. The Rear RV Safety unit comes with a 1 year warranty and can also be hooked to two other cameras if you want side views, etc. You could add one to your entry door or anywhere else you want an outside view.

So, what do you think? Would you install your own back up camera or would you hire someone to do it? Do you have a particular camera unit you recommend? Do you have one you would prefer to avoid?

Place your comments in the box below and then please share this article with all your RV loving friends!  You can tweet, pin. post or share.  Regardless of how you share this article, be sure to come back for more articles about the RV life!

Via: RV Road Trip

As seen on CNN, New York Times, and CNBC: Find out how much money you can make renting your RV Click Here

What do you think?